Citrix Hypervisor (XenServer)

Backup Strategies

XVA-based

In this strategy, the VM is exported as a single XVA bundle containing all the data. Incremental backup is also supported. Data is transferred directly from the XenServer API without the need to set up anything on the hosts.

Backup Process (XVA-based)

• crash-consistent snapshot using hypervisor's API only for full backups

• optionally quiesced snapshot can be done if enabled and guest tools installed inside - if quiesced snapshot has been failed we are doing regular one

• optional application consistency using pre- / post-snapshot command execution

• data export directly from the hypervisor using hypervisor's API - both full (XVA) and delta (VHD for each disk)

• full backup (XVA) contains metadata

• snapshot taken with full backup is kept on the hypervisor for the next incremental backup - if at least one schedule assigned to the VM has backup type set to incremental

• incremental backups are cumulative (all data since last full backup)

• restore recreates VM from XVA, and then applies changes from each incremental backup using Hypervisor APIs

Changed-Block Tracking

In this strategy, the VM is exported using XenServer API (full backup) and the Network Block Device service (NBD, incremental backups) on the XenServer hosts. The CBT feature in Citrix XenServer 7.3+ may require an additional license. The resulting backup has separate files for each disk + metadata, so you also have the option to exclude specific drives.

Note. For full backups only you can still use this strategy without CBT enabled on the hypervisor.

Backup Process (Changed-Block Tracking)

• crash-consistent snapshot using hypervisor's API

• optionally quiesced snapshot can be done if enabled and guest tools installed inside - if quiesced snapshot has been failed we are doing regular one

• optional application consistency using pre- / post-snapshot command execution

• CBT enabled during full backup on each disk if it wasn't done earlier

• metadata exported from API

• full backup - each disk exported from API (RAW format)

• incremental backup - each disk queried for changed blocks and which are exported over NBD

• last snapshot kept on the hypervisor for the next incremental backup - if at least one schedule assigned to the VM has backup type set to incremental

• restore recreates VM from metadata using API and imports merged chain of data for each disk using API

Change Block Tracking setup

Citrix introduced the CBT mechanism in XenServer 7.3. In order to enable CBT backups, the following requirements must be met:

1. Citrix XenServer 7.3 or above must be used - note that CBT is a licensed feature

2. The NBD server must be enabled on the hypervisor

3. The NBD client and NBD module must be installed on vPlus Node

Notes on restore

1. When image-based backups (XVA) are used - vPlus restore VMs as templates and renames them appropriately after the restore

2. When separate disk backups are used:

   • if there is already a VM in the infrastructure with the UUID of the VM being restored (check present flag in VM list) - vPlus restores it as a new VM (MAC addresses will be generated)

   • otherwise, vPlus attempts to restore the original configuration including MAC addresses

NBD Server setup (on XenServer)

1. Get the Network UUID that you intend to use for communication with vPlus - run on the XenServer shell:

   [root@xenserver-cbt ~]# xe network-list
   uuid ( RO)            : e16b4e34-47d4-9a6e-371b-65beb7252d69
          name-label ( RW): Pool-wide network associated with eth0
    name-description ( RW):
              bridge ( RO): xenbr0
   ..........
   uuid ( RO)            : 244a2fa7-ae7c-e45c-819a-44cecf51e8fa
          name-label ( RW): Host internal management network
    name-description ( RW): Network on which guests will be assigned a private link-local IP address which can be used to talk XenAPI
              bridge ( RO): xenapi

   For example: e16b4e34-47d4-9a6e-371b-65beb7252d69

2. Enable the NBD service on your hypervisor:

   xe network-param-add param-name=purpose param-key=nbd
   uuid=<network-uuid>

NBD Client setup (on vPlus Node)

vPlus comes with a pre-built RPM and modules for CentOS 7 distribution.

1. Go to the NBD directory:

   cd /opt/vprotect/scripts/nbd

2. Use yum to install the NBD client:

   yum -y install nbd-3.16.1-1.el7.centos.x86_64.rpm

3. If your Linux does not have the NBD module installed you may try to build one yourself (there is a script for Red Hat based distributions that downloads the kernel, enables the NBD module, and builds it) or use an already provided module.

   You can compile the module by running:

   ./compile_nbd_module.sh

4. Enable the module by invoking the script (the following command will either use a module in your kernel or copy the provided nbd.ko):

   ./enable_nbd.sh

5. Verify that you have /dev/nbd* devices available on your vPlus node host:

   [root@localhost nbd]# ls /dev/nbd*
   /dev/nbd0  /dev/nbd1  /dev/nbd10  /dev/nbd11  /dev/nbd12  /dev/nbd13
   /dev/nbd14  /dev/nbd15  /dev/nbd2  /dev/nbd3  /dev/nbd4  /dev/nbd5
   /dev/nbd6  /dev/nbd7  /dev/nbd8  /dev/nbd9

6. Restart your vPlus Node:

   systemctl restart vprotect-node

Limitations

• VM migration between clusters is not supported.

• Cloning VM to another cluster is not supported.